Front Axle & Steering

Axle Locating Pin for John Deere 2040 Tractors

OD: 40mm: Length: 94mm

Product OEM: L34070, L55437, L63758

King Pin for John Deere 2040 Tractors up to Serial Number 429999

Upper Diameter (Grease Nipple End): 30mm. Lower Diameter: 25mm. Mid Diameter: 49mm. Overall Length: 60mm

Product OEM: L35745

Trunion Pin/Front Axle Bush to suit John Deere 2040 2wd Tractors With Manual Steering.
OD: 31.5mm, ID: 19.74mm. Length: 89.2mm

Product OEM: T21669, L66847

Orbital Steering Unit to fit John Deere 1640 4wd Tractors from Serial Number 430000

Product OEM: AL41291

Track Rod Assembly to suit John Deere 2040 2wd Tractors with Standard Straight Axle.

Taper End: M18x 1.5mm (RH). Straight End: M18x 1.5mm. Length: 428-680mm, Ball Joint Taper: 19-22mm

Product OEM: AL38637, AL82828

Track Rod End (Long) to suit John Deere 2040 2wd Tractors with Standard Straight Axle

Taper End: M18x1.5 (RH). Straight End: 22.2mm. Length: 322mm. Ball Joint Taper: 19.9-22.3mm

Product OEM: 14M7305, AL27533, AL37505, AL82825

Track Rod End to suit John Deere 2040 Tractors with Standard Straight Axle

Taper End: M18x1.5 (RH). Straight End: M24x1.5. Length: 95mm. Ball Joint Taper: 19.9-22.3mm

Product OEM: AL27532, AL37504, AL82826

Steering Joint Lock Nut to suit John Deere 2040 Tractors

M18x 1.5 Thread

Steering Wheel to suit John Deere 2040 Tractors

Splined Centre

Product OEM: AL28457, T22875

Woodruff Key to suit John Deere 1020 Tractor Steering Wheel.

Product OEM: 26H77

Power Steering Cylinder to suit John Deere 2040 2wd Tractors Without Cab

The Brake system must be fully flushed with new clean fluid to remove any residual contaminants that may be left in the system. Warranty shall not be accepted for damaged seals due to contamination.

Product OEM: AL31262

Steering Pivot Pin Bearing to suit John Deere 2040 Tractors from Serial Number 307511 (Heavy Duty Axle) or from Serial Number 307896 (Standard Duty Axle).

OD: 44.45mm (1 3/4"). ID: 31.75mm (1 1/4"). Width: 25.4mm (1").

Product OEM: JD10054

Wheel Hub to suit John Deere 2040 Tractors

Wheel Bearing Hole Dia., Axle End: 65mm.
Wheel Bearing Hole Dia., Hub Cap End: 49.5mm.

Product OEM: R49839, T21545

Wheel Stud to suit John Deere 2040 2wd Tractors

Thread: 9/16" UNF. Thread Length: 1. 1/2". Overall Length: 2". Taper: 45°

Product OEM: JD21

Wheel Hub Gasket to suit John Deere 2040 2wd Tractors

3 Bolt Fixing

Product OEM: A1556R

Wheel Hub Retainer to suit John Deere 2040 Tractors

OD - 90mm. ID - 80.8mm

Product OEM: R26632

Hub Oil Seal to suit John Deere 2040 2wd Tractors

OD: 89.6mm. ID: 60.16mm. Width: 6mm.

Product OEM: AR26480

Spindle to suit John Deere 2040 2wd Tractors

Shaft Length: 380mm. Shaft Diameter: 38mm.

Product OEM: AL28222, AR67416

Spindle Repair Kit to suit John Deere 2040 2wd Tractors

For 38mm Spindles

Product OEM: T21553